Elevator safety parts are only safe as a matched set. A governor is rated by the speed it trips at, the safety gear is rated by the load it can hold, and the buffer is rated by both — mix a 2.5 m/s governor with a 0.63 m/s buffer and the chain breaks at the exact moment it is needed.

This page gives you the rated ranges of the eight devices we list, in the order they act, so you can check a proposed set against your car load and rated speed before you order. Where two models leave a gap, we say so rather than guess.

How elevator safety components work as a chain

Elevator safety components do not work individually. They work in sequence, and each link assumes the next one is rated for the same duty.

  1. Detect — the overspeed governor monitors car speed and trips when it exceeds the set value.
  2. Transmit — the governor rope pulls the safety linkage, which lifts both safety gear wedges at once.
  3. Grip — the safety gear wedges clamp the guide rail and stop the car.
  4. Absorb — if the car still reaches the pit or the top, the buffer takes the remaining energy.

Governor: the device that decides when

The governor is a centrifugal device. Its tripping speed is set at the factory and is not adjustable in the field without re-certification, which is why the rated speed range on the nameplate has to cover your actual contract speed. Our one-way governor OX-240 is rated to 2.5 m/s, uses a 240 mm sheave, and needs a pulling force of at least 500 N to trip the linkage.

Safety linkage: the device that transmits

The linkage converts the governor rope pull into simultaneous wedge lift on both sides of the car. Its key dimension is DBG — the distance between the governor rope centre and the wedge. OX-188T is rated at DBG ≥ 950 mm. If the linkage geometry does not match the safety gear, one wedge lifts before the other and the car stops at an angle.

Safety gear: the device that grips

Two families, two behaviours. Instantaneous gear stops the car almost immediately and is limited to low speed; progressive gear allows a controlled slide and is used at higher speed. Choosing between them is not a preference — the rated speed range decides it.

Buffer: the device that absorbs

Buffers sit in the pit and at the top of the shaft. Their rating combines car speed and the total mass (P+Q) they have to arrest. A buffer rated below the car's speed is not a buffer at that speed.

Matching elevator safety components to car load and speed

This is the table buyers should check first, because the two models we list cover different ends of the market and there is a gap between them.

Model Type Rated load (P+Q) Max speed Guide rail width Typical fit
OX-088 Instantaneous ≤ 1250 kg ≤ 0.63 m/s 10 mm / 16 mm Low-rise, low-speed passenger and goods lifts
OX-188A Progressive 1500 – 6050 kg ≤ 2.5 m/s ≤ 16 mm Medium and high-rise passenger lifts, hospital lifts
There is a gap between 1250 kg and 1500 kg. If your car falls in it, do not force a model — tell us the exact P+Q figure and the rated speed, and we will confirm which unit is available for that range. Publishing a made-up rating would be worse than asking the question.

What P+Q actually means

P is the empty car mass including the sling, cabin, doors and any permanent fitments. Q is the rated load on the plate. Buyers routinely quote only Q, which understates the load the safety gear has to hold by 30–50%. Take P from the car weight record, not from an estimate.

Why the speed boundary is hard, not soft

An instantaneous safety gear stops the car in a very short distance, which means a very high deceleration. Above roughly 0.63 m/s that deceleration exceeds what the car structure and passengers can take. This is why the boundary is written as a maximum rather than a recommendation: a 1.0 m/s car with instantaneous gear is not a conservative choice, it is a wrong one.

Buffer selection by speed and total mass

Buffers are specified last and fail inspection most often, usually because the speed rating was matched and the mass rating was not. This is where elevator safety components orders go wrong most often.

Model Type Max speed P+Q range Guide rail Notes
OH-J11 Rubber / energy-accumulating ≤ 0.63 m/s 500 – 1500 kg 80 – 140 mm Pit-side, low speed
OH-80 Hydraulic / energy-dissipating ≤ 1.0 m/s 600 – 3000 kg 80 mm Pit-side, needs stroke clearance

Energy-accumulating versus energy-dissipating

A rubber buffer stores the impact and gives it back; a hydraulic buffer converts it to heat through an oil orifice. The first is simpler and needs less pit depth, the second is required once the speed exceeds what a rubber buffer can absorb. The 0.63 m/s line is the same line that separates instantaneous from progressive safety gear, and it is not a coincidence.

Pit depth is part of the buffer decision

A hydraulic buffer needs a longer stroke and therefore a deeper pit than a rubber buffer of the same duty. If you are replacing a rubber buffer on an existing lift, measure the available stroke before assuming a hydraulic unit will drop in.

Governors, tension devices and guide shoes

The remaining components are usually replaced one at a time, so their single critical field matters more than their model family.

Governor OX-240

One-way governor, rated to 2.5 m/s, 240 mm sheave, minimum pulling force 500 N. The sheave diameter has to match the governor rope, so quote the rope diameter along with the model.

Tension device OX-300A

The tension device keeps the governor rope taut at the pit end. It is supplied with a 18 kg or 30 kg counterweight in cast iron or barite, with a 200 mm or 240 mm sheave. Match the sheave to the governor, and the weight to the rope length — a long shaft needs the heavier weight to avoid rope slip.

Guide shoe OX-029

Rated to 1350 kg and 1.75 m/s, available for 9 mm, 10 mm and 16 mm rail widths. The rail width is the field that decides fit, and it is measured on the rail head, not on the fishplate. A guide shoe bought on model number alone is the most common wrong part in this category.

Documents, certificates and what we can actually supply

Safety components are the one category where paperwork travels with the part. Buyers ask for test reports and certificates before the price, and rightly so.

What to ask for, and when

Ask for the test report at quotation stage, not at shipping stage — if a model cannot be documented for your market, you need to know before you commit. For a single unit we can tell you what is available for that model; for a project order, list the models and the destination market together.

If the certificate is for a model we do not list

We have had requests for certificates against model numbers that are not in our range. In that case the honest answer is that we cannot document a part we do not supply. Send the model and the standard you need to meet, and we will say yes or no rather than substitute quietly.

Where elevator safety components are inspected

Knowing which test an inspector will run tells you which value on the nameplate matters. Three checks account for most failures on this group of elevator safety components.

Governor trip test

The governor is tripped by hand at the rated speed and must pull the linkage far enough to lift both wedges. If it trips but does not lift, the fault is the linkage geometry rather than the governor — measure DBG before ordering a replacement governor.

Buffer check

Buffers are inspected for oil level, return to rest position, and the rating plate against the car's actual P+Q. A buffer that returns slowly is usually an oil or seal item, not a replacement unit.

Safety gear grip test

The gear is tested for even contact on both rail faces. Uneven marks mean the linkage is pulling one side first, which is a linkage or adjustment problem. Replacing the gear to fix an uneven mark is the most expensive way to solve a geometry issue.

Five fields that make an elevator safety parts quotation usable

  1. P+Q — empty car mass plus rated load, in kg.
  2. Rated speed — the contract speed on the data plate, in m/s.
  3. Guide rail width — measured on the rail head, in mm.
  4. Governor rope diameter — needed for governor and tension device sheaves.
  5. Quantity and destination — one lift or a project, and which market the documents must satisfy.

Missing one of the five is normal. Send what you have with a photo of the data plate; the plate usually carries P, Q and speed, and that is enough to start.

Send the data plate photo. We will read P, Q and rated speed off it and come back with the safety gear, buffer and governor that match — including the ones that do not.

Where these parts sit in the wider catalogue

Elevator safety parts are also the category where a single wrong rating is expensive, so if the car is a modernisation rather than a new build, tell us the year of the original installation as well — rating conventions changed, and a 1990s plate often reads differently from a current one.